random unicornstudio 507 mechanisms

No. 212

Geneva Stop

Clockwork

Six crank turns. Six locked steps. One full turn of the wheel.

01

What it does

Turn the crank. For most of the turn the star wheel does not move. A round locking disc on the crank sits in a hollow flank of the wheel and holds it still. For a short part of the turn a pin on the crank enters a radial slot, walks the wheel around by exactly one slot, and leaves along the same line. On this model there are six slots, so six turns of the crank make one turn of the wheel. Each step is 60°, and the wheel stays locked for the other two-thirds of the turn.

That continuous stepping is the Geneva drive, also called a Maltese cross. Brown’s No. 212 is the watchmaker’s version of the same shape. One flank of the wheel is left convex instead of hollow. When the locking disc comes round to that flank it cannot enter, and the crank stops. Swiss watches used the stop to limit how far the mainspring could be wound, keeping the spring off the tightest and the slackest parts of its range.

Press Watch stop to leave one flank solid. The crank will wind a little past two turns and then meet the flank.

02

How it works

The pin has to enter the slot along the slot, not across it, or it would knock. That one condition fixes the proportions. For a wheel with n slots the pin circle is the centre distance times sin(π/n), and the tips of the wheel sit at the centre distance times cos(π/n). Here the centres are 50 mm and there are six slots, so the pin swings on a 25 mm radius and the tips are at 43.3 mm. The calculator is changing that same rule when you move the slot count.

During the step, the wheel’s angle follows the pin. Call the crank angle θ, measured so that θ = 180° puts the pin straight into the wheel, and write λ for sin(π/n). The wheel speed, as a fraction of the crank speed, is

(λ cos θ + λ²) / (1 + λ² + 2λ cos θ).

It is zero as the pin meets the slot and zero again as the pin leaves. Mid-step, with six slots, the wheel is turning exactly as fast as the crank, and the other way.

Two things are worth seeing on the curves.

The entry is gentle in speed. Because the wheel is still when the pin arrives, a well-made Geneva does not start with a blow. This model leaves 0.35 mm of clearance on each side of the 6 mm pin, in a slot 6.7 mm wide, so a real pin does touch a wall, lightly.

The acceleration does not ease in. Through the long dwell it is zero. The instant the pin takes the slot, acceleration steps to a finite value, changes smoothly through the step, and steps back to zero as the pin leaves. That step is a sharp change of force. At the speed of a finger it is nothing. Spun quickly, it is the knock you hear and the reason the pin wears. Fewer slots make it worse. Three slots are violent. The calculator shows the peak, and the jump at entry.

The lock is a shape, not a spring. While the pin is out, the disc fills a concave flank. You cannot turn the wheel without bending something. That is why a projector frame stays put while the lamp is on it, and why a watch stop can be trusted with a wound spring.

Slots

What changes if you cut more

The slot count sets the step, the dwell, and how hard the pin is worked. Six is this model.

6
Index60°
Dwell66.7%
Crank in motion120°
Peak wheel speed1.00×
Peak acceleration1.35×
Step at entry0.58×
30 rpm

Ideal geometry: no clearance and no friction. The curves match the model.

03

Advantages and limitations

  • Exact index. The step is 360°/n. It does not depend on how hard you turned, or on a pawl landing somewhere in a tooth.
  • A real lock, and a long one. The dwell is most of each turn, and it holds against a load in either direction.
  • A kind entry. Speed starts and ends at zero, so the pin can meet the slot without an impact.
  • Two moving parts. Wheel and driver. The pegs only hold the centres.

The limits are the other side of those choices.

  • The dwell is not yours to pick. It is (n+2)/(2n) of every turn: two-thirds with six slots, three-quarters with four. If you need a different rest, you need a different mechanism.
  • Acceleration jumps. At each end of the step the force changes all at once. Above a modest speed a Geneva gets loud, and the pin takes the wear.
  • The sizes are one decision. Centre distance, pin radius, and slot count are tied together. You cannot stretch the dwell and keep the same wheel.
  • It needs a little air. Without clearance the pin binds in the slot. With clearance, the wheel can move a fraction of a degree at each end of the step before the pin or the disc takes up the gap.
  • It takes room. This is the external form: the driver sits entirely outside the wheel.

04

When to use it

Use a Geneva when a machine needs a locked, exact step at a human pace or a slow motor, and the dwell that belongs to some slot count is the dwell you wanted.

  • Geneva stop. Locked steps, a long dwell, and, if one flank is left convex, a hard limit on how far the crank will go.
  • Ratchet and pawl. Easier to make and easier to hide, and it drives one way. The output is not locked against a load that tries to run backward, unless you add a second pawl. The angle depends on how far the pawl stroked.
  • Cam indexer. A cam can draw almost any acceleration, including a smooth rise with no step at the ends. High-speed packaging machines moved to cams for that reason. It costs a cam, a follower, and someone who can cut them.
  • Internal Geneva. The driver sits inside the wheel. For the same slot count the acceleration is kinder and the package is smaller. The parts are harder to make and to get onto their centres.
  • Mutilated gear. Closer to Brown’s No. 211: a plain arc on the driver locks the pinion, then a toothed arc kicks it round. The teeth meet with a real impact. The Geneva slot is the cure for that impact.

A motor and a sensor will do all of this and then change their minds. The Geneva is the answer when the lock has to be a piece of material.

05

In the world

Film. For most of the twentieth century a cinema projector pulled the film down with a Geneva drive, usually of four slots. One frame advanced while the shutter was shut. Then a long locked dwell, with the shutter open and the lamp on that frame. The dwell had to be still.

Watches. Brown’s use. The stop-work on the barrel lets the key make only a set number of turns, so the mainspring stays in the middle of its torque curve, where a watch keeps better time. Later watches often left it off. The name Geneva stop stayed on the whole family.

Indexing tables. Machining and assembly fixtures still bring the next station under the tool with a Geneva, or with a cam barrel doing the same job, and hold it there while the cut happens.

The same shape turns up in mechanical counters, chart drives, and anywhere a machine has to move, then stay, without a clutch.

06

This model

The parts on this page use the studio’s printable dimensions, in millimetres. The pin circle and the wheel tips follow from the centre distance and the slot count. Drag the crank, or press play. Lift separates the parts. Watch stop leaves one flank convex, which is Brown’s stop rather than the continuous drive.

Slots6
Index60°
Dwell66.7% of each turn
Centres50.0 mm
Pin circle25.0 mm
Wheel tips43.3 mm
PinØ 6.0 mm
Slot width6.70 mm
Locking discØ 36.0 mm
Clearance0.35 mm a side
Wheel thickness5.6 mm

The picture is not a scan of the STL mesh. It is these profiles, extruded, so the clearances you see are the clearances in the file.